Hana Modz V3 DNA 40
Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen
-
-
Oh mann meine Hanas sind bei mir daheim angekommen und ich bin am arbeiten, so ein misst
-
-
So bin so schnell nach Hause gefahren wie ich konnte...war etwas aufgeregt
Ich habe gehofft das Cedric sein wort hält und mir statt Gunmetal mir in Schwarz liefert weil keine in polished als 18650 gab...packet aufgemacht und was sehe ich auf der Verpackung GUNMETAL
War voll enttäuscht weil Gunmetal nicht mein ding ist....falls jemanden diese Farbe gefällt und eine Hana haben möchte, gebe jemanden die chance einer zu erwerben und das zum Preis was ich bezahlt habe
Jedoch brauche ich eine antwort bis morgen bevor ich sie zurück schicke.
Die Mini sieht sowas von cool aus hier Bilder
IMAG0742.jpg -
[Links nur für Registrierte]
Hier läuft ne Preorder:
[Links nur für Registrierte]
Sieht super aus, die Kleine[Links nur für Registrierte] -
Jetzt.
-
Finaly here
Connector was a bit crooked, but my hammer solved the issue
-
-
Moin zusammen,
ich habe eine kurze Frage. Wie ist eigentlich der 510er Anschluss im (bzw. am) Gehäuse befestigt?Jetzt. -
Da scheint ein neues Modell auf dem Weg zu sein: Mit DNA 40 und "Temperature Protection"
40 Watt Variable Power Module with Temperature Protection
The HANA MODZ MINI Pack V3 is a DNA 40 temperature protected device. The body is made of 6061 Billet Aluminum. Built in DNA charger; which is MICRO USB powered and provides a 500 milliamp charge current. The DNA 40 is a power regulated digital switch-mode DC-DC converter for personal vaporizers. It features Evolv's patented Wattage Control, Temperature Protection, Preheat, Step up/Step Down Topology, Digital User Controls, OLED Screen, Onboard Buttons and Synchronous Rectification for maximum battery life and minimal heat generation. It is the most advanced personal vaporizer controller ever made.
Specifications Minimum Typical Max
Output Power 1 watt 40 watts
Output Voltage 1 volt 9.0 volts
Output Current, continuous 16.0 amps
Output Current, instantaneous peak .16 Ohm .7 Ohm 2.0 Ohms
Atomizer Resistance, temperature sensing wire, cold .10 Ohm .4 Ohm 1.0 Ohm
Temperature Limit 200 F 450 F 600 F
Input Voltage 3.1 volts 3.7 volts 4.3 volts
Input Current .5 amps 8.0 amps 16.0 amps
Screen On Current 25mA
Quiescent Current 1mA
Power Down Current 5uA
Efficiency 92%
Weight 6g
Footprint .65" x 1.30" .80" x 1.30"
Thickness .32"
Screen Size .69 OLED
Temperature Protection
The DNA 40 is the first power supply for electronic cigarettes to directly measure and limit the temperature of the heating coil during operations. By preventing the coil from becoming too hot regardless of fluid, wicking or airflow, a variety of undesirable situations can be prevented. For example, appropriate temperature settings will prevent the wicking material from charring, which compromises taste and introduces unintended chemicals into the vapor. Appropriate temperature setting will also reduce the breakdown of flavoring and base liquid components, which could impact taste or safety.
Evolv's Temperature Protection Technology requires a heating coil made from Nickel 200 alloy, rather than Nickel Chromium or Kanthal alloys. Nickel 200 is commercially pure nickel. It is often sold in vapor shops and online as "non-resistance wire". If the temperature reaches the maximum value, the wattage applied to the atomizer coil is reduced to prevent overheating. Please note that the temperature reading is the average temperature of the atomizer coil so that the temperature is uniform, without hot or cold spots. Ensure that the coil does not short to itself.
Because wattage, not temperature controls vapor volume, large vapor volumes can be produced without unnecessarily high temperatures. Temperature Protection is most helpful if the atomizer begins to dry out, the user pauses during a puff, the beginning or end of the puff, or if the wattage setting is inappropriate for the attached atomizer.
In normal operation, when the device is not firing the maximum temperature setting is displayed on the screen. When the device is firing, the actual average temperature of the coil is displayed on the screen.
[Links nur für Registrierte][Links nur für Registrierte] -
Jup - zum neuen Chip gibt's seit gestern ein [Links nur für Registrierte] mit Brandon von Evolv - wen's interessiert
-
da wird keine Temperatur gemessen.. sondern lediglich eine aus irgendwelchen angenommenen Werten berechnete Temperatur angezeigt. Man nehme den Temperaturkoiffizienten von Nickel und werfe den mitsamt dem gemessenen Widerstand und der gerade produzierten Spannung in irgendwelche Formeln. Ob die Coil gerade komplett im kühlenden Liquid steht, oder furztrocken dryburnt.. oder ob ich da über 25 Luftlöcher nen Wirbelsturm durch den Verdampfer jage interessiert dabei die Anzeige rein gar nicht
Hört sich nett an.. aber braucht keine Sau Aber immerhin kann der Chip Step up/Step Down
-
Yep, die Temperatur wird "ermittelt" anhand der Veränderung des Widerstands des Nickeldrahts.
-
DNA40 hat doch was gutes
DNA30 und 20er sollten eigentlich günstiger werden- Wer im Mittelpunkt steht, steht im Weg!
-
Braucht kei Sau die Temperaturanzeige. Ich sehe den Vorteil des neuen Chips im Step down und endlich ist ein Schutz gegen falsches einlegen der Batterie vorhanden. Naja Evolv will halt auch Geld verdienen die müssen ja jährlich irgendwas neues bringen. Aber wie Disarstar schon sagt der Preis für DNA30 wird fallen. Somit ein positiver Nebeneffekt.Lieber einen Tripper als nen Egripper
-
Teilen
- Facebook 0
- Twitter 0
- Google Plus 0
- Reddit 0
-
Ähnliche Themen
-
Information